now small lory finally received the award for the candy "What was LOOK!" , courtesy of the binding of square stock and barrel, I can post how.
materials
- cardboard, thickness 1.5 mm (usually the bottom of the sketchbook or block is fine): 2 rectangles 20x15, 5 cm (cover), a rectangle 19x14, 5 cm (frame); 1 strip 19X2, 3 12.2 cm strips and 2 x2, 3 cm (thickness);
- cloth binding: a rectangle 23x6, 3 cm (zip), a rectangle 22x17, 5 cm (frame) and a 7x7 cm square (corners);
- coordinated paper: 23x15 cm 2 rectangles, a rectangle 30.8 x19 cm;
- Optional: a sheet of acetate which acts as a "glass";
- cutter, glue, ruler and team;
- books or weights in general
work!
1) Photo Frame: - FRAME from the rectangle of cardboard, cut a window with team and cutter to 3 cm all around the perimeter and bonded on three sides thicknesses, which create the hole space photography.
- on canvas, marked the swing of FRAME, leaving a margin of 1.5 cm for the external part for the tuck;
FRAME - spigoletti cut the canvas, so you can tuck better. the measure of distance from the box should correspond approximately to the thickness (in this case, 3 mm, because of the frame over the boards). I hope the photos you understand how to tuck the corners because I do not know how to explain it in words, however, if anything, ask!
- carve with a knife "X" crossing the central canvas from edge to edge, and cut the surplus, however, always leaving a border of 1.5 cm to be able to tuck:
it! mettela hours upside down with the thickness up and under a weight.
2) The COVER
time ago I posted a tutorial for a colorful album: the cover is done in the same way, but since this time there are sharp and that I remembered to take photos of various steps, I explain again.
- the measure of the width of the hinge I obtained by overlapping two plates and cover the frame and measure the thickness and this I have added more than 5 mm with 5 cm "decorative".
on the paper side of the canvas I drew a line by line off a distant 1.5 cm from the top and bottom edges (always for tuck) and for a long 3 cm from the respective left and right edges, so that in the middle part has created a channel.
paste the cartoons on this side and beyond the trench and rolled up the usual 1.5 cm.
- draw within the square canvas edge 1.5 cm wide (guess what? always tuck!) and a diagonal cut along the oblique line and you will get two triangles for the corners. glued into place (the edges of the tuck will be the guide) and, as you see in the picture on the left, check the top of the triangles as we did earlier for the frame and rolled up.
- now it's up to the paper: the part without corners, take one of the rectangles, draw the usual margin of 1.5 cm on the two short sides and one of those long, overlapping the paper glued to the canvas of 0.5 cm; rolled up.
for the facade with the corners rather than the need to remove the outer corners:
here is not cut at random determined that the paper overlaps of 5 mm on canvas, calculated and less-sat-ta-as-you must be great to eliminate the slice. unfortunately I have not pinpointed the measure, but if you work on the hypotenuse edge of the ruler of cloth and easily find the size you need. If you are afraid of making mistakes, rather than do a test with a piece of ugly! again glued and rolled. - now the hard part: the inside cover. Here we must be quick and accurate ... First, you make small subtle signs here and there at 5 mm from the edge (this space is called unghiatura). Then, apply adhesive to the back of the card, starting from the center outwards. lift it, remove half of the paper or whatever it is you used to not to get any glue on the table and using the references that you path, position the sheet. then press it all with a clean cloth. an area not doing so great wrinkles and air bubbles is practically impossible to "stretch" the paper, use the pleat or back of the spoon and press down on, with repetitive movements until it settles. if the bubble moves and you can not just take her closer to the end so I can go out with a compass needle pierce thin and press. it may be created "pimple effect" and that the little hole a bait fillet glue rag in hand, and assorbitela spalamatela above, both the PVA glue is transparent and not seen. there But remember to leave the stain on the canvas, so if you happen to the canvas, push the bubble towards the exit: the canvas is strong and can act more forcefully than the card.
- at this point, put under a weight for a couple of hours and make tea (or put in place a bit 'casino that has been done in the meantime ...)
3) ASSEMBLY
here is simple : spreading glue on the back of the frame on the three strips and apply to one of the inner covers, towns because it is slightly smaller, the opening to insert the photo is facing the hinge, for pure aesthetics.
at this point the frame is again put under a weight, but put them scraps of paper under the frame to prevent the weight of the face where bulging has no support.
if you like you can put a sheet of acetate to an extent, that protects the photo from dust. for measuring small lory photos (10x15 cm) was enough package that divides the two floors of ferrero rocher box parallelepiped. but do not do the bullshit that I did to stick it to the frame! because the work is finished I realized I did the measures too much "sucked" so it makes an effort to put the photo Executioner.
if happen to you but here's a remedy:
Dahn-tah!
ah! you know why I call it frame by journey? because you can close like a book and put in a suitcase (or drawer)
0 comments:
Post a Comment